SLAT-4SB,5SB,6SB,7SB
* The main function is scoring and slitting on corrugated board.
* Slitting capacity: 4 out (slitting tool 5 sets, and scoring tool 8 sets)
* 5 out (slitting tool 6 sets, and scoring tool 10 sets)
* 6 out (slitting tool 7 sets, and scoring tool 12 sets)
* Slitting and scoring bracket's shaft: diameter 123mm; surface grinded and chrome plated.
* With thin blade slitting knife: 270mm; minimum slitting size 135mm.
* Each slitting knife using independent grinding system; can set grinding time and length for slitting knife from computer, and also can grinding by manual to make sure the clean and smooth on paper board's cut.
* Using oil cooling system; operating with grinding system.
* Using A.C. motor + Inverter for slitting tool.
* Diameter of scoring tool: 224mm; Minimum scoring size110mm.
* A.C.Inverter motor + Inverter for scoring tool can synchronous operate with Double Backer.
* Pneumatic controlled raising and lowering of slitting and scoring tool; two machine ally order change without stop machine or cut off paper board while machine is running.
* Slitting and scoring size adjustment by independent motorize setting; Max. to Min. size setting time 13 seconds.
* Up to 999 order changed can stored into memory.
* Production order No. can output from memory by actual needed.
* The machine can motorized move right or left 50mm to adjust paper's slanting.
* Motorized waste paper suction equipment right or left.
Option:
* Scoring type can change to three scoring types.
RRLT-4SB, 5SB, 6SB, 7SB
* Slitting capacity:
4 OUT (slitting tool: 5 sets, scoring tool: 2 sets and total is 8 scorings)
5 OUT (slitting tool: 6 sets, scoring tool: 2 sets and total is 10 scorings)
6 OUT (slitting tool: 7 sets, scoring tool: 2 sets and total is 12 scorings)
* Structure is double scoring devices and adds one is slitting system.
* Slitting and scoring use precise linear bearing and ball screw.
* Top single blade diameter 270mm.
* Minimum slitting size: 175mm.
* Slitting type using top slitting design. Each blade has independent grinding and oil fill system, which can set up blade grinding of production meter according to paper material.
* Diameter of upper scoring tool: 224mm.
* Lower scoring tools can furnish four types scoring device, with male to male, male to large female, male to small female and male to flat.
* Minimum scoring size: one set scoring tool: 165mm, two set scoring tool coordination: 0mm. With scoring depth control system.
* Slitting and scoring base movement control by independent motor that could finish size adjustment within 13 seconds.
* With automatic paper pressing and avoid paper bending device in the middle of scoring and slitting tool.
* Up to 999 order changes can be stored into memory.
* Can output any order according to actual demand.
* Machine can left to right movement 75mm that adjust by motorized motor.
* With motorized web suction equipment.
* A.C. Inverter motor + Inverter for scoring tool, A.C. motor + Inverter for slitting tool (Control separately).
* Synchronization with Double Backer.
* Using two units ally with operation to order change without cut off corrugated board or stop machine.
RRLB-4SB, 5SB, 6SB, 7SB
* Slitting capacity:
4 OUT (slitting tool: 5 sets, scoring tool: 2 sets and total is 8 scorings)
5 OUT (slitting tool: 6 sets, scoring tool: 2 sets and total is 10 scorings)
6 OUT (slitting tool: 7 sets, scoring tool: 2 sets and total is 12 scorings)
* Structure is double scoring devices and adds one slitting system.
* Slitting and scoring use precise linear bearing and ball screw.
* Single blade use down slitting design, diameter 270mm and upper scoring device using urethane.
* Minimum slitting size: 175mm.
* Using down slitting type to scoring can effectively improve printing side of corrugated board's fish-tail problem.
* Each blade using independent motorized motor and can independent adjust blade entry amount.
* Using gradually blade entry and setting by corrugated board's thickness. (signal send from production manager system).
* Each blade has independent grinding and oil fill system, which can set automatic grinding time and length by computer; also can grinding by manual, to make sure corrugated board's cut smoothly.
* Diameter of upper scoring tool: 224mm.
* The height of lower scoring tool cannot adjust and upper scoring tool adjusted up and down by air cylinder; with scoring depth control system.
* Lower scoring tools can furnish three types scoring device, with male to male, male to female and male to flat.
* Minimum scoring size: one set scoring tool: 165mm, two set scoring tool coordination: 0mm.
* Slitting and scoring diameter adjust by motorized motor, and the diameter adjustment within 1~13seconds.
* Up to 999 order changes can be stored into memory and can output any order according to actual demand.
* Machine can left to right movement 75mm to fit with web edge-guide.
* With motorized web suction equipment (computer per-set).
* A.C. Inverter motor + Inverter for scoring tool and scoring tool using the same motor with Double Backer; can synchronous operate and ally with Double Backer.
* Using two units ally with operation to order change without cut off corrugated board or stop machine.
